Adam belt shield
Our belt shields can be painted in groups colours, insignia or heraldry to show the membership to a certain group. Made from 1,2 mm steel, we offer them in our favorite plate armour series now. Matching the "Adam" series, this shield is decorated with the series' typical ridge along the edge. It is worn on a belt by using the two loops on the top to hoist it through there. Naturally it can be worn as a tasset, when fastened on the upper thigh. This way you will have an additional plate armour piece. The belt shields, just like our arm shields, cry out to be painted, modded and to be combined with existing clothing. This is, where your creativity and immagination comes into place. Talking of creativity: We suggest to clean the shield with Acetone prior to painting it. Afterwards just sand it with a paper with 600 grid. Use some automobile colour primer as the colour-matching foundation. When the foundation is fully dried, you should sand it again and apply a second layer of colour. Now is the time, where you can paint your details, like heraldry, animals and writings with weatherproof acrylic paint. Material: 1,2 mm steel Length: 24 cm Width: 18 cm Weight: app. 350 g
Adam bracers
Our "Adam" bracers are a little bit shorter than their cousins from our other series. Because of this they will also fit adolescents or smaller people. Additionally, like all the other "Adam" armour parts, it has a corrugation along the rim.Material: 1.2mm steelColour: blank, brownedMeasurements: 20cm length, 17cm on top, 13cm on the bottom
Adam breastplate
Our breastplate "Adam" is something special. Its design was inspired by the first complete breastplates from the 14th century. Metal lamellae protect the sides and the lower back.This piece of armour is fastened by two buckles on the backside. Maybe you take a look at our Padded Jackets to wear them underneath your Armour. This maximizes the comfort wearing it.You might want to consider a combination with a Chainmail Shirt? Material: 1,2mm steelColour: blank, browned
Adam gorget
The "Adam" gorget captivates with simple elegance. Two embossed ornamental beads are not only jewelry, they also give the collar a lot of stability. All edges are of course, as with all Mytholon armor, crimped. Thanks to its simple shape, this gorget can be used for all imaginable armament concepts. All the spaulder from our plate armour range can be attached to this collar. Material: 1, 2mm steelShoulder blade width: 8cmTotal width: 33cmNeck length: 14cmFront length: 22cmTotal length: 46cm Weight: 1 kg Colour: blank, browned
Adam Greaves
Our "Adam" greaves are pieces of light leg rmour that are also well-suited for the younger generation. They feature the ornamental border typical for the "Adam" series. For an average adult, these greaves will approximately reach down to the middle of the calf. Material: Steel Measurements: 30cm length, 22cm on top, 15cm on the bottom The price refers to one pair.
Adam guard set
We offer you the "Adam" guard set, consisting of bracers & greaves for a discounted set price. Material: 1.2mm steel
Adam spaulders large
The big shoulders of the "Adam" series have a three-segment lamellar. It is attached to a generous, two-part shoulder segment and gives the wearer a lot of mobility. Like the entire "Adam" series, these large shoulderarmour has a simple elegance. The typical bead adorns the curved main segment and gives it additional stability. The large shoulders are good to complement a heavy armour and can be combined with any Mytholon plate gorget. Material: 1, 2mm steelTotal length: 30 cm Top length: 17 cm Top width (curve): 34.4 cm Bottom width: 21 cmWeight: 2.3 kg
Adam spaulders small
Our small "Adam" spaulders are perfectly suited to be worn as additional armour over chainmail or leather armour. Due to their size and the flexible lamellae covering the upper arms, these pieces will not encumber you in any way.Material: 1.2mm steelWidest arm circumference: 56 cmTightest arm circumference: 34,5 cmColour: blank, browned
Alberto morion
The Morion developed from the Bascinet originally. The high dome is typical for this form. It was popular with pikemen, city militias and body/imperial guards. You can still find it with the swiss guard of the vatican today. OnesizeMaterial: SteelColour: blank
Alwin bascinet
The Alwin bascinet with chainmail aventail is based on a 14th-century European helmet type. Worn by knights and soldiers throughout the late Middle Ages, it ranks among the classic helmet forms of the period. The deep-drawn, pointed helmet bowl offers solid all-around protection for the head, neck, and shoulders – especially in combination with the attached mail. A notable feature of this model is the removable nasal bar, which provides additional facial protection when needed and can be mounted or detached with just a few steps – ideal for varied portrayals or practical use. The interior features a fixed foam lining for comfort, and a fully adjustable chin strap ensures a secure fit. Material: Steel (helmet), steel rings (aventail), foam (padding), synthetic leather (strap) Ring diameter of mail: approx. 9 mm Size: suitable for head circumference approx. 56–62 cm (not individually adjustable but the inlay can be removed)
Arlan conical helmet blank
Kegelhelmets were widely spread in medieval asia and europe in many different variations.This one has some cheek flaps, a high dome to protect the skull, and ends in a crest of horses\\' hair. The maille protects neck and chest area.UnisizeMaterial: Steel\\"Colour\\": blankWe suggest to wear this helmet with a padded coif \\"Leopold\\" to avoid scratches and bruises on the head. This will improve the comfort wearing it.
Baldric normans helmet
This normans helmet is equipped with a nasal, which gives additional protection to the facial area. It developed across europe in the early and high medieval times and spread quickly across the entire continent. The classical form of this helmet is manufactured with a high dome and a nose guard ("nasal").We suggest the combination worn with a blank chain coif and one of our padded coifs to be worn underneath this helmet.Colour: blank, brownedInner circ.: 61cm
Balthasar belt shield
Our belt shields can be painted in groups colours, insignia or heraldry to show the membership to a certain group. Made from 1,2 mm steel, we offer them in our favorite plate armour series now. Matching the "Balthasar" series, this shield is decorated with rivets and a beading along the edge. It is worn on a belt by using the two loops on the top to hoist it through there. Naturally it can be worn as a tasset, when fastened on the upper thigh. This way you will have an additional plate armour piece. The belt shields, just like our arm shields, cry out to be painted, modded and to be combined with existing clothing. This is, where your creativity and immagination comes into place. Talking of creativity: We suggest to clean the shield with Acetone prior to üainting it. Afterwards just sand it with a paper with 600 grid. Use some automobile colour primer as the colour-matching foundation. When the foundation is fully dried, you should sand it again and apply a second layer of colour. Now is the time, where you can paint your details, like heraldry, animals and writings with weatherproof acrylic paint. Material: 1.2 mm steel Length: 24 cm Width: 18 cm Weight: app. 350 g Colours: blank, browned
Balthasar bracers
As with all other products from the "Balthasar" line, these bracers have a rim decorated with rivets. The combination of a rounded outline and decorative elements make them look both noble and warlike. Material: 1.2mm Steel Length : 23cm Width top: 18cm Width bottom: 14cm Weight (Pair): ca. 1,0 kg
Balthasar full armguard
The armguard from the "Balthasar" series is very elaborate and is made up of nine flexibly connected segments. This ensures maximum agility in combat. With the ornamental rivets and beading typical of the "Balthasar" series, the armguardr is well suited to complement a "noble" armor. Each Mytholon shoulder armour has a belt on its underside in which this armguard can be mounted. In this way, various combinations and armament concepts are possible. Material: SteelColours: blank, brownedLength: 46 cmWeight: 3,8 kg
Balthasar full legguard
The "Balthasar" leg guards are made of six segments. Their knee joints are very agile and hardly hinder running or fighting. Like all the armor parts of the "Balthasar series", the leg guards are intricately designed and decorated with beadings and rivets. The lower leg segment is kept short, so additional tassets can be worn. This increases the agility and gives the armor an extra detail. For knights, paladins and other heavy armored charactres, the "Balthasar" leg guard is an ideal complement. Material: 1,2mm steel Colours: blank, browned Length: 57 cm Weight: 4.7 kg
Balthasar gauntlet
This gauntlet is made from eight pieces and provides good protection from blows to the hand and forearm.The long cuff is closed on the bottom. The gauntlet is closed with three buckle-straps and fits tight to most hands.The beadings and rivets match the entire "Balthasar" series.The leather gloves are not included in delivery.Material: 1,2mm steelColours: blank, brownedLength: 29cm, Width on back of hand: 17cmWeight: 1750 g
Balthasar gorget
The "Balthasar" gorget is a very stylish piece of armour. Elegant lines and decorative rivets along its edges, make it stand out of the mass.This gorget can also be combined with all other Mytholon spaulders. To make them look their best we recommend combining them with other "Balthasar" armour parts.There are two different "Balthasar" gorgets. We recommend the smaller size for the leaner necks of ladies and adolescents. We recommend the larger size for gentlemen.Small: Length front part: 23cmTotal width: 29cmLarge:Length front part: 29cmTotal width: 36cm Material: 1,2mm SteelColours: blank, brownedYou can find all our "Balthasar" series products here.Maybe take a look at our Padded Jackets to wear them underneath your Armour. This maximizes the comfort wearing it.
Balthasar greaves
As with all other products from the "Balthasar" line, these greaves have a rim decorated with rivets. The combination of a rounded outline and decorative elements make them look both noble and warlike. Material: 1,2mm Steel Length: 35 cm Width: 23 cm Weight (Pair): ca. 1,5 kg
Balthasar guard set
We offer the "Balthasar" bracers & greaves for a discounted set price. Material: 1.2mm steel Size greavesLength: 35 cm Width: 23 cm Weight (Pair): ca. 1,5 kg Size bracers Length : 23cm Width top: 18cm Width bottom: 14cm Weight (Pair): ca. 1,0 kg
Balthasar set
Our "Balthasar" armour series does not only look great and worthy, but also allows a free movement when fighting. The spaulders and the torso are made from lots of movable parts. This is why the "Balthasar" series offers the movability, you would normally find only with custom built armour. The full arm guards are quickly attahed to the spaulders and are made from six seperate pieces (riveted to each other) providing lots of movement. The typical series' rolling shapes are found in the full leg guard as well. They are attached to the wearer by using the two upper leather straps on the hip belt. Just like all pieces from the armour series, the armour parts are decorated with the typical round head rivets. The greaves are worn seperatly and are not attached to the full leg guards. This enhances the comfort wearing them. This set is a high quality basis for any knights or warriors costume. It combines a premium entrance to any battlefield with movability, efficiency and comfort. We suggest to wear a padded gambeson underneath all metal armours, as it will increase the comfort and avoid bruises and scratches. This armour can be upgraded with a chainmail to recieve a heavy armour appearance. This set contains: - the "Balthasar" greaves- the "Balthasar" spaulders large- the "Balthasar" full arm guard- the "Balthasar" full leg guard- the "Balthasar" torso armour Material: 1,2mm steel Measurements of the torso armour: Chest circumference: app. 115cm to app. 130cm Length: 72cm Weight of the chest plate: app. 4,2kg Weight of the back plate: app. 4,4kg Measurements of the spaulders: Length: 27cm Width: 49cm Weight (pair): app. 3,4kg Measurements of the full arm guard: Length: 50cm Circumference (wrist): 25cm Width on the shoulder strapping: 25cm Weight (pair): app. 3,8kg Measurements of the full leg guard: Length: 57cm Width of the calf segment: 26cm Width of the thigh segment: 34cm Weight (pair): app. 4,7kg
Balthasar spaulders large
These are our big "Balthasar" spaulders. Just the right thing for knights and other nobles. Although they are rather big and decorated, these spaulders are "ready for the field".The spaulders are composed from seven parts and therefore very flexible in movement.Material: 1.2mm steelColours: blank, browned
Balthasar spaulders small
The small shoulders "Balthasar " provide high stability with maximum mobility. Each of the four flexibly connected segments was fitted with a bead and the typical Balthasar riveting strip. This does not only look very noble, it also significantly increases the stability of the segments. Together with sturdy rivets made of solid steel, these shoulders hold many battles without deforming. They are well suited to complement a ' noble ' armor and for all armor carriers that want to show some prosperity. Like all Mytholon plate shoulders, this one is of course compatible with all our plates gorgets. Material: SteelLength: 31 cmWeight: 1.5 kgsColours: blank, burnished
Balthasar torso armour
The torso armour from our "Balthasar" series consists of two pieces: the chest and the back plate. Both are connected with a strap on each side and a strap on either side of the shoulders. That allows an individual adjustment for each wearer. The chest plate is made from seven seperate segments which are riveted to each other. Its moving parts underneath the arms allow a free movement and agility of the wearer. The elaboratly made back plate is rigid and decorated with lots of rivets. The lower two segments are moveable and allow a bending of the upper body. The matching big spaulders can be attached to the shoulders of the armour. Rolling shapes and segments, just as the offset bordering and the decoration with rivets, add structure and character to this great armour. We suggest to wear a padded gambeson underneath all metal armours to avoid scratches and bruises on the body. This adds lots of comfort when wearing the armour. Material: 1,2mm steel Circumference (chest): app. 115cm to 130cm Length: 72cm Neck: 21cm Weight (chest): app. 4,2kg Weight (back): app. 4,4kg
Berthold sallet
This helmet shows a high, pointed scull piece with an enlongened neck protection. The part on the forehead is riveted to the helmet and provides an additional protection to the wearer. The scull part is made with a spine.The visor can be moved upwards to allow a better breathing for the wearer in between battle moments.The helmet is made with an inner inlay of foam (covered in cotton) and has a chin strap attached.The sallet is a very common helmet type for the late medieval period and was often worn in combination with gotic armourment. It was used later as well, especially by bandits and sellswords, who scavaged them off the battlefield.Material: 1,2mm steelSize: up to 62cm circumferenceColour: blankWe recommend to wear a padded coif underneath to avoid scratches and bruises. This will maximize your comfort.
Blacwin nasal helmet
This typical Norman helmet is based on historical models and has its root in Northern Europe during the 11th and 12th centuries. This makes it an ideal helmet for the portrayal or Nordic characters. Norman helmets are often seen worn by Viking characters. If this helmet shape looks familiar, that's probably where you've seen it before. The helmet has an inner lining.The nasal helmet was a variant of the spangenhelm featuring a nose-guard (nasal) that sometimes becomes wider towards the end. The helmet's top part is tapered, increasing its protective effect. As opposed to spangenhelms made of several parts and two-part visor helmets, nasal helmets were more commonly forged from a single iron plate from the 10th century on. Chainmail coifs were often worn under nasal helmets for additional protection.Material: steelSizes: small (56-58) and large (59-66)Colours: blank and burnished
Bragi helmet blank
A classical viking helmet with a long nasal. It has got pretty curved applications in the front. The pointed toppart is reinforced with two crosswisely riveted steel straps. This gives it a militant look and makes it more robust against blows. It has got a cotton covered foam padding on the inside and two leather straps to make it fit tightly to the head.Material: 1mm Steel
Edward helmet Discontinued
Discontinued, only while stocks last The matching helmet to our armor series Edward. Its design is based on historical great helmets, but with more dynamic shaped eye slits. Like all pieces from this series the offset beading and the decorative rivets make it a real eye-catcher.The helmet has a circumference of 60cm to 62cm, so it is made for larger heads.Material: Steel 1,2mmColour: blank, browned with blank edges
Einar viking helmet
This helmet is made with a round scull cap and finished with a protector for the eyes. The cap itself is decorated with two metal bands crosswise and another along the bottom edge.The "Brillenhelmet" is mostly found with nothern people of the germanic tribes and can be used in reenacting vikings.Material: 1,2mm steelSize: up to 62cm circumferenceColour: blankWe recommend to wear a padded coif underneath to avoid scratches and bruises. This will maximize your comfort.
Eindal normans helmet
This helmet was designed following the exsample of the nothern european normanns helmet:Having a noseguard riveted to it´s forehead, this helmet should be renamed nasal helmet.It was widely spread over the entire continent, not exclusevly known to the normanns only. In it´s typical form this helmet has a high headpiece and the noseguard.Suitable not only for early-medieval or norman characters... We suggest to wear the combination of a chain coif or a padded coif with this helmet.Material: 1.2mm SteelColour: blank, browned
Elias full arm guard Discontinued
Discontinued, only while stocks last This full arm plate armour from our series "Elias" protects from shoulder to the wrist. It has a joint on the elbow and is therefore very moveable.The offer does not include the gorget and shoulders.Material: 1.2mm steelColour: blankSold as a pair.All other articles from our \\"Elias\\" series can be found here.
Elias full legguard blank Discontinued
Discontinued, only while stocks last These full leg plate armours from our "Elias" series are blank and protect your legs from ankle to the upper thigh. The knees have a joint and therefore do not interfere with movement.Material: 1.2mm steelColour: blankAll other \\"Elias\\" series\\' articles are listed here.Sold in pairs.
Elias spaulders large
The large, segmented spaulders from our "Elias" series.The original, "typical" spaulder has a segment added to it and therefore looks even more impressing. The spaulders are being fixed by a buckle-strap on the gorget, and a single strap under your upper arm. The gorget is not included.Material: 1.2mm steelColour: blank, brownedSold in pairs.
Elias spaulders small Discontinued
One of our "Elias" series' spaulders. They are being fixed to the wearers' gorget, by using the belt-buckle. Use the single stap under your upper arm. The gorget is not included in this offer.Length: 22 cmWidth over curvature: 37.5 cmColour: blankSold in pairs.
Elias torso short blank Discontinued
The short breastplate from the "Elias" series is kept simple and functional. The chest and back plate are connected by flexible leather pieces on the shoulders. This not only increases the mobility, it also allows a quick fitting and displacement of the armor. Of course, this armor also has suspensions for spaulders. It is closed with straps on the sides by which the size can also be adjusted. Thanks to its plain and simple straightness, the short breastplate "Elias" is very suitable for guards, soldiers or mercenaries. It is also a good base to build a heavy armor on it. Material: SteelWeight: approx. 2 kgColor: blank
Fafnir brigandine
Our "Fafnir" body armour is something really special. Metal plates have been riveted on a backing of padded suede. Especially the comfort of the wearer and the feasibility of putting on a complete suit of armour in a few minutes were our goals. Because of this there is no need to wear a gambeson or a similar garment.You have the choice between three different adjustments which you can make yourselves. The different parts of the armour are connected by leather straps. The three different sizes are achieved by pulling these straps through eyelets. Additionally, you can omit some parts of the armour, eg. the shoulder parts or the thigh protectors.In our opinion, the browned version of the "Fafnir" armour is specially suited to be used as armour for dark and evil NPCs, because they won`t need much time to arm themselves. Material: Suede, Leather, SteelLength: 96-107 cmBreast circ.: 104-114 cmShoulder width: 52 cmArm length: 27 cmWeight: ~12kgLeather is a product of nature and may take dyes differently. The actual hue may differ from the image.
Fafnir brigandine set
Our "Fafnir" body armour is something really special. Metal plates have been riveted on a backing of padded suede. Especially the comfort of the wearer and the feasibility of putting on a complete suit of armour in a few minutes were our goals. Because of this there is no need to wear a gambeson or a similar garment. You have the choice between three different adjustments which you can make yourselves. The different parts of the armour are connected by leather straps. The three different sizes are achieved by pulling these straps through eyelets. Additionally, you can omit some parts of the armour, eg. the shoulder parts or the thigh protectors. The complete set of our "Fafnir" line of products, consisting of: Fafnir bracersFafnir greaves Fafnir brigandine Material: Steel, suede, leather, cottoncanvas
Fafnir padded bracers
The bracers "Fafnir" consist of three fixed riveted segments. A wrist guard, an extra padded segment to protect the elbow and the actual bracers. With their curved lines and the wide beading, the bracers look sleek and elegant, with maximum protection. Due to the overlapping segments, they are very stable and do not deform even in the case of heavy duty. Like all the armor of the "Fafnir" series, these bracers are also equipped with padded suede upholstery. This increases the wearing comfort considerably and also protects against bruises. They are closed with sturdy leather straps and roll buckles on the back. Armours of the "Fafnir" series are not only for characters with "Nordic" background a decent protection. Adventurers, knights, soldiers and many other armour wearers also benefit from their good protective effect and maximum wearing comfort. Material: 1,2 mm steel, suede, polyester Length 33 cm Weight 1.7 kg
Fafnir padded greaves
The "Fafnir" greaves consist of three solid riveted segments. A lower foot protection, which, thanks to the generous, padding, allows the greaves to be comfortably worn down to the boots, an extra padded segment for the knees and the actual protection for the shin. With their curved lines and wide beading, the greaves look sleek and elegant, with maximum protection. Due to the overlapping segments, they are very stable and do not deform even in the case of heavy duty. Like all the armour of the "Fafnir" series, these greves are equipped with padded suede upholstery. This increases the wearing comfort considerably and also protects knees and feet. They are closed with sturdy leather straps and roll buckles on the back. Armours of the "Fafnir" series are not only for characters with "Nordic" background a decent protection. Adventurers, knights, soldiers and many other armour wearers also benefit from their good protective effect and maximum wearing comfort. Material: 1,2 mm steel, suede, polyester Length 53 cm Weight 2.7 kg
Falerio shoulder armour
The Falerio shoulder is part of our Beasthunter series and was developed for fighters who want to combine mobility with reliable protection. It is worn on one shoulder and combines a multi-part plate shoulder with a small breastplate, which is securely fixed to the body with an adjustable leather strap.The articulated shoulder lames offer a high degree of freedom of movement and follow the natural movements of the arm. Thanks to its asymmetrical design, the Falerio shoulder is especially suitable for hunters, mercenaries, rangers or monster hunters and gives every outfit a distinctive, functional character. Made from robust steel and fitted with high-quality leather straps, the shoulder can be combined with other armour pieces from the Beasthunter series as well as with many other plate or leather costumes.Material: steel, leatherChest circumference approx. 58 cm to 68 cm
Fidelio barbute
The barbute is the italian variant of the bascinet and offers good protection for head and face without limiting view or breathing to much.We recommend wearing a padded coif with it.
Francis helmet
According to its shape the helmet "Francis" is a kind of kettle helmet from the late middle ages. This version has got a very long drawn brim that makes for a specially good face protection but limits the sight of the wearer a lot more than the standard kettle helmets.It has got a cotton covered foam padding on the inside and two leather straps to make it fit tightly to the head.Material: 1mm Steel
Franz open sallet
The sallet is the successor of the kettle helmet in europe and one of the most common helmet types in 15th century in the western hemisphere. There is types with visor and without, often with a segmented neck protection, but mostly with a stiff one.The "Franz" sallet is built without visor, so it does not cover the face and keeps it open for the wearer to breath free and a better vision.The edge along the face, and following, the complete lower edge, is corrugated. The centre ridge is built very low to keep the silhuette rounded. This helmet is equipped with a cotton covered foam inlay and has a leather chin strap.Material: 1,2mm steelColour: blankSIze: up to 62cm circumferenceWe recommend to wear a padded coif underneath to avoid scratches and bruises. This will maximize your comfort.
Fredrik vikings helmet
This type of helmet stands out for the viking era in europe. The skull is protected by a rather high dome, which has an additional eye-protector. This simpler kind is especially good for the interpretation of a German warrior or a early-medieval Norman.Material: 1.2 mm SteelColour: blankWe suggest to wear a chain coif and a padded coif underneath. This will improve the interpretation of the role...
Friederich abdominal armour blank
This simple abdominal armour is perfectly made for combination purposes. Its being closed with a single buckle strap in the back. This way we ensure to make it very comfortable to put on and off by yourself. Looks good when combined with a shirt of browned chainmaille and/or a dark padded jacket. We suggest it as part of a Landsknechts' costume. It is closed with a buckle in the back.Material: 1,2 mm steelWidth: 40 cmHeight: 25 cm
Galahad belt shield
This small belt shield completes the "Galahad" torso armour.Use the two buckles to strap it to the centre part of the chest plate and to cover up the unprotected parts in your crotch.It may be a small armour piece, but it brings a huge effect to any armour, as it can be used to paint heraldic colours on it. This shield can also be added to any exsisting armour, but may need some handiwork to get it attached.Material: 1,2mm steelColour: blankSize: onesize Our products are handcrafted, so dimensions and colour tones may vary slightly. Photographic images and screen settings may not accurately represent colour tones.
Galahad Paladin armour set
The plate armor came to Western Europe at the end of the 14th century and was used until the 17th century. It has been continuously developed and adapted to the respective needs of its carriers. So it is not surprising that there were a lot of variants of this armour.The "Galahad" plate armour is a three-quarter harness in fantastic design. Striking are the massive shoulders with the big blade crushers. With their large floating discs, they give the armor its impressive, powerful character. The torso is segmented and flexible. It is adjustable in size and passes into a armourbelt. Attached to this belt are the curved tassets. Between them sits a belt shield."Galahad" is ideal for heavily equipped roles such as knights or paladins. The armour can be supplemented by arm and leg guards as well as with a chainmail. Material: SteelThickness: 1.2 mmColor: Shiny
Galahad spaulders
A pair of huge spaulders, equippe with sword breakers and besagew on each side.The spaulders are made from multiple parts that are riveted together. This way the wearer will still be able to move his arms freely and is not limited in movement.The sword breakers on the inside enlarge the entire spaulder from the side view. Use the inner buckle to strap the spaulders to the \\"Galahad\\" torso armour; additionally there is a buckle-strap for the upper arm. The besagew cover the armpit, the place with auxilliary arteries - vital parts, so to say. This is the armour part, where you have the possibility to paint your own heraldic colours onto. A small colourful armour piece will loose up the complete blank look of the armour.Material: 1,2 mm steelLength: 44 cmWidth: 44 cmCircumference: approx. 60 cmWeight: 5.9 kg